Burnham V8 Series Bedienungsanleitung PDF herunterladen (Seite 66)

100

Burners), hold for one (1) second and release to

reset primary control.

3. On STEAM BOILERS:

a. With an L404A1354 - set cut-out pressure

(MAIN scale) on the pressure limit for (2) PSI

and differential pressure (DIFF. scale) below

(2) PSI. These pressures may be varied to suit

individual requirements of the system.

b. With an L404A1651 or an L404F1367 - set cut-

out pressure (MAIN scale) on the pressure limit

for (1) PSI and differential pressure (DIFF.) for

.5 PSI. These pressures may be varied to suit

individual requirements of the system.

4. On STEAM BOILERS WITH TANKLESS

DOMESTIC WATER HEATERS, set boiler

water temperature dial on L4006 operating control

at 190°F (max.). Set differential at 10°.

5. On WATER BOILERS WITHOUT TANKLESS

HEATERS, set high limit dial on L8148 at 180°F.

This temperature may be varied to suit requirements

of installation.

6. On WATER BOILERS WITH TANKLESS

HEATERS, set operating control dial (low limit)

on L8124 at 190°F and high limit dial at 210°F.

Operating control (low limit) must be a minimum of

20° below high limit setting. Set differential at 25°.

E. ADJUST OIL BURNER BEFORE STARTING.

1. CHECK BURNER AIR BAND AND AIR

SHUTTER, readjust if necessary, see Table 6 at

rear of manual.

NOITUAC

rofteserarettuhSriAdnadnaBriA

rofdetsujdaerebtsumdnatupnimumixam

otroirp,sreliobMWrosreliobmaets

.renrubgnitrats

2. Beckett Burners

a. Inspect Beckett head setting on left side of

burner by insuring the blue line MD(V1) or the

line on the label MB(L1) are aligned, readjust if

necessary.

b. OPEN ALL OIL LINE VALVES.

c. Attach a plastic hose to fuel pump vent ﬁ tting

and provide a pan to catch the oil.

d. OPEN FLAME OBSERVATION PORT

COVER on burner swing door.

e. Beckett burners for boiler models V83 thru V86

are factory equipped with (2) nozzles for dual

ﬁ ring rates. On packaged boiler models PV83W

thru PV86W, the higher ﬁ ring rate nozzle is

installed; on knockdown boiler models KV83W/

S thru KV86W/S both nozzles are shipped loose.

Refer to Table 6 at the rear of this manual for

proper nozzle size, air settings and fuel pump

pressure setting based on desired ﬁ ring rate.

If the desired ﬁ ring rate is the lower GPH:

1) replace the loose or factory installed high

ﬁ ring rate nozzle with the loose lower ﬁ ring

rate nozzle,

2) change the factory air settings according to

Table 6 and,

3) reduce the oil pump pressure on models V83

and V86 to the pressure setting speciﬁ ed in

Table 6, refer to Paragraph F for details.

3. Carlin 102CRD Burners

a. Inspect Carlin head setting on left side of burner

by reading the scale embossed on the housing.

Refer to Figure 7A and Table 6 of this manual.

b. OPEN ALL OIL LINE VALVES.

c. Attach a plastic hose to fuel pump vent ﬁ tting

and provide a pan to catch the oil.

d. OPEN FLAME OBSERVATION PORT

COVER on burner swing door.

e. Carlin burners for packaged and knockdown

boiler models V87 thru V89 are provided with

one nozzle, installed in the burner, that provides

the same ﬁ ring rate for both the steam and water

boiler builds.

4. Carlin Elite EZ Burners

NOITUAC

tsumdnatupnimumixamroftessidnaBriA

MWrosreliobmaetsrofdetsujdaereb

.renrubgnitratsotroirp,sreliob

a. Inspect Carlin head setting on left side of burner

to ensure that the proper head positioning bar

matches the nozzle that is installed in drawer

assembly. Replace bar if necessary.

b. OPEN ALL OIL LINE VALVES.

c. Attach a plastic hose to fuel pump vent ﬁ tting

and provide a pan to catch the oil.

d. OPEN FLAME OBSERVATION PORT

COVER on burner swing door.

e.. Carlin burners for boiler models V83 thru V86

are factory equipped with (2) nozzles for dual

ﬁ ring rates. On packaged boiler models PV83W

thru PV86W, the higher ﬁ ring rate nozzle is

installed; on knockdown boiler models KV83W/

S thru KV86W/S both nozzles are shipped loose.

Refer to Table 6 at the rear of this manual for

proper nozzle size, air settings and fuel pump

pressure setting based on desired ﬁ ring rate.

If the desired ﬁ ring rate is the lower GPH:

1) replace the loose or factory installed high

ﬁ ring rate nozzle with the loose lower

ﬁ ring rate nozzle,

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 99 100

Kommentare zu diesen Handbüchern

Keine Kommentare

Burnham V8 Series Bedienungsanleitung Seite 66

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserkocher Burnham V8 Series